English saddle
From Wikipedia, the free encyclopedia
English saddles (as opposed to Western saddles) are used to ride horses in English riding disciplines throughout the world. The discipline is not limited to England or English-speaking countries. This style of saddle used in all of the Olympic and FEI equestrian disciplines, except for the newly-approved FEI events of equestrian vaulting and reining. Most designs were specifically developed for jumping or moving quickly across rugged, broken country with fences. Unlike the western saddle, there is no horn or other design elements that stick up above the main tree of the saddle.
Contents |
[edit] Parts of the English saddle
- Tree: the base on which the rest of the saddle is built. It is eventually covered in leather or synthetic material as the saddle is built. The stirrup bar is built onto the tree.
- Panels: the part of an English-saddle which provides cushioning between the horse's back and the saddle, and allows adjustment in fitting the saddle to the horse. Also important in keeping the saddle balanced for the rider. Often flocked with wool, foam, or air pockets. The panels under the cantle are called the "rear panels." Those at the front of the saddle are called the "front panels." However, the rear and front panels are one continuous unit, which can be seen if the saddle is flipped over. The saddle has two panels total, one on each side of the horse's spine.
- Gullet: The channel between the panels of the saddle, which provides clearance for the horse's spine so the saddle does not place pressure on it.
- Seat: the dip in the saddle where the rider's seatbones rest, it is the lowers part of the saddle's topline. The deeper the seat, the more security is provided for the rider.
- Pommel: the front the saddle, which is raised higher than the seat both to provide security for the rider and to give wither clearance.
- Cantle: the back of the saddle, which is raised higher than the seat to give security.
- Waist: the part of the saddle between the seat and the pommel, on which the rider's pelvic bone rests. The width of the waist has a great effect on rider's comfort, especially for women riders.
- Skirt: piece of leather that goes over the stirrup bar, to help prevent the rider's leg from rubbing on the buckle of the stirrup leather (which is adjusted so it is right against the stirrup bar). It also helps to keep the buckle of the stirrup leather from unbuckling and sliding down. The skirt is easily lifted up to adjust the stirrup leather.
- Saddle flap: The large piece of leather on an English saddle that goes between the rider's leg and the billets and girth buckles. It helps prevent the horse's side from being pinched by the stirrup leather. The shape and length of the saddle flap is directly related to the intended use of the saddle, as it must mirror the rider's leg position.
- Sweat flap: The large piece of leather that goes between the billets and the horse. It helps to protect the rest of the saddle from the sweat of the horse. It is not seen in monoflap saddles.
- Billets (girth straps): Straps which are secured from the saddle tree and hang down, to which the girth is buckled. They have several holes in them to adjust the tightness of the girth. There are generally three billets (one spare), although some saddles have two long billets to buckle the girth lower down (below the saddle flap).
- Buckle guard: the billets are threaded through the buckle guard, which protects the saddle flap from getting worn away by the buckles of the girth. These are not always present on saddles with long billets, which are intended to be buckled below the saddle flap.
- Knee/Thigh roll: padding on an English saddle that is right under the knee and in front of the thigh, helps give the rider more support. It may be very thick in some saddles, very thin (called pencil-roll), or not present at all.
- Calf block: padding that falls behind the rider's lower leg, helps to keep it in place and stabilize the rider. It is commonly not present, except on certain saddle models.
- Stirrup: part of the saddle in which the rider's feet go, provides support and leverage to the rider.
- Bar: part of the tree of the saddle which allows stirrups to be attached. It is made of strong metal. The stirrup bar is usually kept in the "open" position, so that (should the rider fall and start to be dragged) the stirrup leather can release off the saddle, freeing the rider. There are only a few instances in which the bar should be kept in the "closed" position.
- Iron: The metal part of a stirrup, in which the foot of the rider rests. It provides support and leverage. It is usually made of stainless steel, not iron.
- Leather: The part of the stirrup which attached the stirrup iron to the stirrup bar of the saddle. It can be adjusted to change the lengths of stirrups. Leathers is correct plural useage.
- Stirrup leather keeper: keeper sewn onto the saddle flap, through which the extra stirrup leather is passed. Keeps it neatly out of the way so it doesn't get under the rider's leg. Some saddles simply have a slot cut into the saddle flat, through which the leather is passed.
- D-ring: a metal "D"-shaped ring on the front of an English saddle, to which certain pieces of equipment (such as breastplates) can be attached. They can occasionally be pulled out of the saddle when under great stress.
[edit] History of the English saddle
During the 18th century, most riders in Europe used high-pommel and cantle saddles, with a wooden frame for classical dressage. This saddle was based on a model used for bull fighting, cattle work, long-distance travel, and mounted combat, as its high pommel and cantle helped to provide the rider with support. This saddle is still used today, most notably by the Spanish Riding School, and also in Iberia and eastern Europe.
In England, foxhunting grew in popularity (as the usual quarry of deer had dwindled following the English Civil War, when they were hunted for food). This required a new type of riding, as horse and rider now had to tackle fences, hedges, ditches, and banks straight on if they wished to keep up with the hounds and witness the kill. The old saddle was cumbersome while hunting. Its cantle would get in the way of the riders as they tried to lean back over the fence (a practice that was common until Caprilli developed the "forward seat"), and the high pommel created pain as the rider went over jumps. The resulting saddle developed for foxhunting had a very low pommel and cantle with a flat seat, and no padding under the leg, therefore providing the rider with little, if any, support. The stirrup bars were protruding, and placed more forward than modern saddles, which made it nearly impossible for the rider to keep his legs underneath his body. However, the usual practice was to ride with longer stirrups, and the feet pushed out in front, so this was not a problem.
The English hunting saddle is the predecessor of all English-type riding saddles. As the sports of show jumping and eventing became more popular, saddle shape changed. Caprilli, Santini, and Toptani developed the "forward seat," in which the rider uses shorter stirrups and keeps his legs under him as he rode in two-point, with his seat bones hovering above the saddle. The shorter stirrup required a more forward flap, to match the greater knee angle of the rider. The protruding stirrup bars were uncomfortable in this new position, so they were recessed. The waist of the saddle was also made narrower. Additionally, padding was placed under the knee rolls, for extra security.
[edit] Differences from Stock saddles
The term English saddle encompasses several types, including those used for show jumping and hunt seat, dressage, Saddle seat, horse racing and polo. To non-horsemen, the major distinguishing feature of an English saddle is its lack of a horn. However, some Western-influenced saddles, such as those used to ride rough stock in rodeos and certain types of western-influenced saddles used in endurance riding, lack a horn as well. These saddles can still be classified as western-influenced, however, due to the deep seat, high cantle, prominent pommels, wide fenders (stirrup leathers) and large, leather-covered stirrups. In addition, saddles used for working cattle in nations other than the United States, such as the Australian Stock Saddle and the Charro Saddles of South America, often share features such as a deep seat and extra leather to protect horse and rider, but lack a horn.
The other major characteristic which defines an English saddle is that it has panels: these are a pair of pads attached to the underside of the seat and filled with wool, foam, or air. Although some modern saddlers have developed alternative models, the English saddle is usually constructed on a framework known as a tree. The tree is made of wood, spring steel, or composite, and it supports the rider on a sling of webbing between the firm pommel (front of the saddle) and cantle (back of the saddle). On either side of the tree, a steel hook known as the "stirrup bar" is affixed. It is upon this hook that the rider hangs the stirrup leather, which is a very strong leather or nylon loop supporting the stirrup. At the bottom of the tree are several more very strong leather or nylon straps known as billets, to which will eventually buckle the girth--the beltlike strap which holds the saddle onto the horse.
The tree and its various parts are upholstered with a covering made of leather, nylon or microfiber and shaped to form the seat above and the panels below.
In addition to the seat and panels, English saddles feature a leather flap on either side called, appropriately, the flap. The flap sits between the rider's leg and the horse's side and protects the horse from being pinched by the stirrup leather. On some saddles it is also specially padded to protect or support the rider's knee.
[edit] Styles of English saddles
The differences between the styles of English saddle are small but significant. The most important distinctions are the location of the seat, and the flap length and shape. A saddle used for a discipline where the rider sits more upright with a longer leg, such as in dressage, has a flap that is longer to accommodate the leg, and less inclined forward (as the knee doe not need to go forward). The seat will also be closer to the withers, to keep the rider's center of gravity in the correct spot. However, in disciplines where the rider needs shorter stirrups for extra support, such as in the jumping disciplines, the saddle flap is moved proportionately forward and shortened, and the seat is moved further back. A jumping saddle will have a shorter and more forward flap than a dressage saddle, with the seat slightly more towards the cantle. If the flap was not inclined forward, the rider’s knee would hang over the flap, and the flap would constantly push the leg out of position (usually backward), so that the rider would become unstable and interfere with his horse. If the seat was not moved rearward, the rider would be forced ahead of the saddle over a fence. A racing saddle, where jockeys ride with incredibly short stirrups, will have an extremely forward and short saddle flap (almost more horizontal than vertical), and the seat will be extended very far back from the pommel to keep the rider’s center of gravity correctly situated.
Padding is also considered when developing a saddle. While a polo saddle is constructed with a minimum of padding so as to allow the polo player great freedom to twist and reach for his shot, a saddle used for jumping or eventing may have more padding to help give the rider support over fences. A newer development is the monoflap saddle, which removes the sweat flap, keeping only the saddle flap, thus eliminating one layer of leather between the rider and the horse, and giving a closer feel.
[edit] All-Purpose or Eventing saddle
The "all-purpose" or "eventing" saddle (also sometimes called a "general purpose" saddle) was developed to allow riders to use one saddle both over fences and on the flat. This type of saddle has a deep seat with a long, but somewhat forward flap. The flaps usually have padding under the leg, for support while jumping. The design is intended to be a compromise between the flatter "close contact" jumping saddle with a forward flap, and deep-seated dressage saddle with a long, straight flap.
This style of saddle is most commonly seen in amateur-owner or lower-level junior competition. The less-expensive "all-purpose" models are often marketed as beginner's saddles. More expensive models are usually labeled "eventing" saddles. Manufacturers insist that there is a significant design difference between an eventing saddle and an all-purpose saddle. However, while eventing saddles usually do have better balance and higher quality materials and workmanship, a fundamental design difference is otherwise difficult to discern. Many manufacturers create two models, one with a slightly straighter dressage-oriented flap that still allows a rider to jump low fences, and another with a more forward flap that allows a rider to jump somewhat more challenging fences, but still permit a deep seat for flat work. One company manufactures a design with a flap that can be adjusted to be straighter or more forward, as the rider prefers.
Due to the deep, secure-feeling seat, the design is also used by some people when starting young, unpredictable horses, and is quite popular for trail riding, endurance riding, and casual hacking. Many top-level endurance riders find this design superior to an "endurance" style saddle for distance competition because it allows them to get off the horse's back and move quickly over rough or mountainous terrain, yet provides greater security to the rider. On the other hand, this compromise design also means that an advanced rider may find the saddle limits his or her ability to obtain a correct position at higher levels of competition, either in show jumping or dressage. For this reason, many English riding instructors and coaches do not particularly encourage their riders to use these saddles.
Quality and balance are very critical factors to consider when purchasing an all-purpose saddle. Many cheap models are designed with a too-forward cut flap that is not properly aligned with the seat, which prevents the rider from getting into a correct position on the flat and sometimes gives the rider the uncomfortable sensation of feeling like they are constantly sliding backwards. Also, when the stirrups are adjusted correctly for jumping, the rider's knees are then too far behind the flap (this is especially true for shorter riders). Some models also are too high in the cantle, which can hit a rider in the buttocks and push them forward when jumping all but the smallest fences.
[edit] The Jumping saddle
See also: Show jumping, Hunt seat
The jumping saddle, sometimes called a "forward seat" or "close contact" saddle, is designed for show jumping, hunt seat equitation, foxhunting, and the stadium and cross-country phases of eventing. Its most distinctive feature is a forward-cut flap that allows for a shorter stirrup length (although not as short as racing stirrups). The flap often has supportive padded knee rolls, especially for show jumping and cross-country, less so for hunt seat. The balance of the seat is further back and comparatively flat, with the cantle and pommel low so that they don't interfere with the rider's jumping position (known as "two-point position" or "half-seat").
Like the All-Purpose saddle, the jumping saddle usually has three short billets. However, newer styles (such as monoflap jumping saddles),these have longer billets that mirror the dressage saddle, so that the rider no longer has to ride with extra bulk under his/her leg.
It is important that the rider's leg fit appropriately into the flap of the jumping saddle when she has her stirrups shortened. If the knee is too far forward or back, the rider's balance will be incorrect and the saddle becomes a hindrance than an advantage while jumping obstacles.
[edit] Dressage saddle
See also: Dressage
Dressage saddles have a very straight-cut flap, much longer in length than a jumping saddle, which accommodates the longer leg position of a dressage rider, who works only on the flat and does not need to jump fences. The pommel is a bit higher and the deepest point of the saddle's seat more forward, all to allow for this longer leg position.
The seat is usually much deeper in a dressage saddle than a jumping saddle, and allows the rider to comfortably sit and relax to best influence the horse. The stuffing of the panels is often kept to a minimum in a dressage saddle, to allow a closer feel with the horse. It often has a wider bearing surface than a jumping saddle.
Some designs feature an exaggerated amount of padding in front of the knee, much more than in a jumping saddle, to assist the rider in keeping the knee down and thigh back. However, there is usually little padding behind the calf, as the rider needs to be able to freely move her lower leg around to give aids to the horse.
The billets of most dressage saddles are very long, to allow the girth to be buckled near the horse's elbow rather than underneath the rider's leg (which would get in the way of giving effecting leg aids). However, some dessage saddles come with shorter billets.
[edit] The Saddle seat saddle
- see also Saddle seat
The Saddle seat saddle, also sometimes called a "Park," "Lane Fox" or a "cutback," is a variation on the English show saddle. It is used on the gaited breeds of the Americas, including the Saddlebred, Tennessee Walking Horse, Paso Fino, and Missouri Foxtrotter. It is also used in non-gaited but action-oriented classes in the USA, Canada and South Africa for breeds such as the Morgan and the Arabian.
The seat of this saddle is longer and flatter than that of a forward seat or dressage saddle, placing the balance of the rider farther back. The pommel is always cut back to allow greater freedom of the front legs and shoulder, as well as to accommodate the higher withers typical of the saddle seat breeds. The flap is wide front-to-back, ending closer to the cantle than any other English saddle so that the rider's leg (whose thigh is further back than usual due to the seat being further back) is protected. Riders use very long stirrups, usually at least as long as those of Dressage riders. Riders sit farther back on the horse than in other English riding disciplines, though correct Saddle seat equitation still demands that the rider's legs and feet be balanced under the horse.
The Saddle seat was developed from two sources. The first was a flatter European saddle developed to sit the rider further back to show off the high front leg action of flashy horses, often seen quite literally during Sunday rides in city parks. (See English Show Saddle, below.) The second source was the plantation saddle developed in the southern United States that allowed riders to sit back comfortably on a gaited horse as they covered large areas of land on a daily basis.
[edit] Endurance saddle
See also: Endurance riding
The Endurance saddle is used for the long-distance competition of endurance riding. Its major task is to provide the horse and rider with the comfort and balance needed to cover long distances over rough terrain, sometimes for multiple days. For the rider, the seat is often quilted or padded, and the stirrups are designed with a wide foot tread to reduce fatigue. For the horse, the panels skirts of the saddle are extended to provide a larger area of contact with the back, thus reducing fatigue linked to the pounds per square inch of saddle contact. The saddle has many dee rings along the pomnel and cantle that allow the rider to attach various items.
Originally based on a military or police saddle, modern endurance saddle manufacturers have been innovative in methods to lighten weight and provide additional comfort for the horse, and several of these techniques have gone on to influence other saddle types. The panels are stuffed with different types of material, all designed to spread pressure evenly and disperse sweat. Most endurance saddles may have extended panels (called "fans"), which increase bearing area. Others may have "floating" panels, which are particularly useful since endurance riders often ride with their seat out of the saddle (releasing pressure from the back, but increasing the amount felt on the stirrup bars where they attach near the point of the tree).
There is also an endurance saddle design based on the western saddle that is a bit larger and heavier, but is designed with similar goals.
[edit] English showing saddle
This saddle is used in the United Kingdom, Australia, and elsewhere, for showing, and is a direct descendant of the English hunting saddle. The show saddle is designed to show off the horse's conformation, most notably the shoulder, and is therefore a very minimal saddle with a close fit and straight-cut flap. The seat is very flat, and there are no knee or thigh rolls, so the saddle offers little support to the rider. Like the American Saddle Seat saddle, the English showing saddle has a stirrup bar set farther forward and a cutback pommel that falls behind rather than over the withers. Many show horses are also presented in fatter condition than in more athletic disciplines, so the billets are placed to help keep the saddle properly placed on a rounder animal.
The traditional position of the rider was to ride with the feet placed forward, and the seat pushed back, which was once thought to encourage more action and to make the horse look as if he has a longer front end. Modern competitors are starting a trend to a more classical position, with the leg placed underneath their body and their hips over their heel. This position is much more forgiving on the horse's back and actually encourages better movement. The traditional English showing saddle is not used by these riders, and instead a more dressage-like saddle is used, with a more vertically cut flap. There sometimes is slight padding in these saddles, providing extra support, and the horses themselves are often shown in leaner, more athletic condition.
[edit] Sidesaddle
Main Article: Sidesaddle.
The sidesaddle was used by women from approximately the 14th through 19th centuries, when a combination of long skirts and social mores discouraged women from riding astride. Today the saddle is still used for specialty purposes in shows, parades, and other exhibitions, though also for practical purposes by some riders who have injuries that make it difficult to ride astride. A smaller number of riders feel that sidesaddle riding is a skill and riding art worth preserving and thus continue to practice the style, working to achieve greater skill and refinement. Sidesaddles may be used in almost every discipline, including show jumping. The four main divisions in modern horse shows are Western, Hunt seat, Saddle seat (the two english divisions use the same basic style of saddle but different bridles and rider appointments), and "historical," which may depict any culture or period, but must be fully researched and correctly utilized.[1]
Although sidesaddles are still manufactured today, it is a small niche market, and a new sidesaddle is quite expensive. Thus most riders who wish to ride sidesaddle are often found hunting for older saddles at antique shops, estate sales, and in dusty barn lofts. It is difficult to find a sidesaddle that not only fits the rider and horse but also is in good condition.
The sidesaddle has only one stirrup leather, and two pommels: the fixed and the "leaping horn." Although there are some sidesaddles that lack a leaping horn, they are not considered safe by modern standards. Both pommels greatly help the rider to stay in place, even when jumping. In fact, it may be difficult for the rider to be thrown free should the horse fall. The vast majority of sidesaddles are designed so riders sit with both legs on the near (left) side of the horse, though occasionally a sidesaddle is found that is reversed and allows the rider to sit with their legs to the off (right) side. In spite of having both legs to the side of the horse, a properly positioned rider sits on the horse facing forward, with their spine centered in the saddle perpendicular to that of the horse, with weight balanced equally on both buttocks.
The seat must be wide enough to accommodate the rider's offside thigh as well as buttocks. A sidesaddle is comparatively flat with a small curved pommel and a long, raised cantle on the off side to support the offside thigh and to help the rider keep her spine squared on the horse's back. The near-side flap is commonly cut forward to keep the rider's right leg and foot from touching the horse's left shoulder. The girthing is usually a three-buckle system, with a usual full-length girth as well as a balancing girth. The stirrup of a sidesaddle is much shorter than in a conventional saddle, so that the rider's knee is placed close to the leaping horn, and it buckles midway down the leather rather than close to the tree.
The sidesaddle also comes in both English and Western designs, usually determined by the underlying tree, girthing system, flap or fender design, styling features and type of leather used. However, the structure of the fixed pommel and leaping horn is a consistent design feature across all riding styles.
[edit] Racing saddle
See also: Horse racing, Steeplechase
The flat racing saddle is designed to not interfere with a running horse and to be as lightweight as possible (including the stirrup irons). This saddle provides very little security, placing the rider in a position that allows a horse the freedom of movement needed to achieve maximum speed, but at the cost of giving the rider less leverage to control the horse. Therefore, racing saddles are not suited for general equestrian riding.
Most racing saddles weigh less than four pounds; the lightest saddles weigh as little as 11 ounces.[citation needed] This saddle generally has only one billet to attach the girth, and so an overgirth is usually added to keep it secure. Saddles used in steeplechases are generally slightly heavier and more substantial. The racing saddle has a very long seat without a dip to it, combined with extremely forward flaps that accommodate the very short stirrups and extreme forward seat used by jockeys. It also has a flat pommel and cantle so nothing interferes with the jockey.
Exercise saddles are usually larger and heavier, with a more prominent pommel and cantle to provide more security to the rider. Though these features add pounds, weight does not matter as it would in a race.
[edit] Polo saddle
See also: Polo
The polo saddle is designed specifically for the mounted game. It has a relatively flat seat and the saddle flaps are long and fairly straight to accommodate the longer leg position, although more forward than the dressage saddle.
One of the defining features of the polo saddle is that there is very little or no padding under the leg, allowing the rider to have maximum freedom of movement. If the saddle had thigh or calf blocks, the leg would not be allowed to swing forward or back as needed.
[edit] Fitting the English saddle
There are many factors to consider when fitting a saddle, and it is always best to get a trained professional to fit a saddle to a horse's back. Incorrectly fitting saddles cause pressure points, which may result in bruising, soreness, and problems under saddle. Symptoms of poor fit include:
- Sore back, which may cause the horse to no longer lie down or no longer roll
- Hollowing of the back and raising the head while under saddle
- General stiffness
- Shortness of stride
- Unwillingness to work, napping (refusal to go forward), or excitability
- Bucking, rearing, bolting
- Refusal of fences
- Uneven wear on the feet
- Intermittent or unexplained lameness
- A "cold back"
Long-term, the topline may start to deteriorate, and the horse will develop the wrong muscles. The muscles of the back may waste away and atrophy, causing hollows right behind the withers and it may look like the withers have gotten higher and sharper.
[edit] Correct placement
Before fitting the saddle, it should be placed correctly on the back. Most riders put their saddles too far forward, especially those that use jumping saddles, which causes several problems including:
- Interference with the horse's shoulder blades as he extends his forelegs or as he folds his legs over fences. This also is damaging to the saddle, as it causes twisting.
- Causes the pommel to rise up, tilting the cantle down and moving the seat back, so it is impossible for the rider to maintain a correct balanced position. This not only makes it extremely difficult for the rider to ride, but also places the majority of weight on the horse's loins.
- The tree points are more likely to dig into the withers, as the withers are wider closer to the neck then they are at the back. This causes extreme discomfort for the horse.
- The girth will be more forward, which can result in rubbing.
- The stirrups fall too far back, and pressure from the rider's feet cause them to go too far forward, resulting in a "chair seat" by the rider, making a balanced position very difficult.
Therefore, the front edge of the saddle should be behind the shoulder blade when the front legs are extended as far as possible. This can be done by having someone on the ground pull each of the horse's forelegs as far forward as possible, holding the leg at the knee, while another person checks the shoulder blade. Even a well-fitting saddle will cause great discomfort and serious problems for the rider if it is placed too far forward.
The rider's weight should be carried on the muscles that are over the horse's ribs (from behind the shoulder blades to the last rib). The last rib of the horse should be found, and the saddle should not come behind it. Saddles that are too large (for example, a 17" saddle used on a medium or small pony), or saddles that are placed too far back, will put pressure on the horse's loins, which is very uncomfortable for the animal, and may be damaging.
[edit] Tree size
The tree size, which dictates the width of the saddle, is one of the most important factors when fitting the saddle, and can be tested easily by looking at the sweat pattern on the animal's back after work. A tree that is too narrow is more of a threat than one too wide, as it pushes the points of the saddle into the horse's back. This will often result in a hollowing if it persists for long periods of time. The sweat pattern will have even sweating along the panels, except for the points of the tree, which will cause round dry spots in the area of sweat, as a result from the pressure.
A saddle that is slightly too wide will not be a problem. However, a saddle that is much too wide will not have adequate wither clearance, especially on a high-withered horse, and will cause great pressure in this area and damage.
[edit] The panels
The panels should have even flocking. This can be tested by running the hands down the panels while applying slight pressure. If the panels are stuffed unevenly (one panel higher than the other, or stuffing that is hard and lumpy rather than smooth), the saddle will have pressure points and could cause soreness. A saddlefitter should also check to make sure that the pannels are correctly stuffed for the horse. The front panels should have pressure evenly distributed down their front, which can be tested by saddling the horse with a girth, than running the hands down the front panels to feel for even pressure. The back panels should not rise off the horse's back as he is ridden.
The bearing surface of the panels should be as large as possible (within reason). Poor stuffing or pressure points on the saddle will decrease the bearing area.
[edit] Height of the gullet
The saddle should provide adequate clearance for the spine and withers. With the horse's heaviest rider sitting on the saddle, there should be at least three fingers width between the pommel and the withers, and it should be possible to shine a light down the gullet and see it out the other side. The gullet should also be about three inches in width all the way down, pommel to cantle.
[edit] Fitting the rider
The fit of the saddle to the rider is also critical, as a poorly-fitting saddle will disrupt the rider's balance and cause her to fall backwards, or develop incorrect form as a way to compensate as she fights to maintain balance in the saddle. Even excellent riders can not ride well in a poorly balanced or fitted saddle, so it is best to find a model that is comfortable and allows the rider to easily maintain the correct position.
- Pommel/Cantle height: the cantle should be slightly higher than the pommel, and the seat should not be too far back (which would tip the rider backward and force the lower legs forward).
- Seat: the seat should allow about one hand's width behind the rider's seat and in front of the pelvis, with the rider centered in the saddle. A saddle that is too small makes the rider insecure, and is uncomfortable to ride, a saddle that is too big does not provide any support for the rider. Some female riders (due to their naturally wider pelvis) often prefer a wider seat. A narrow seat may cause backache, joint pain, and even cases of persistent headaches in female riders. It is best to try different models to see which is most comfortable.
- Saddle flap: the rider should shorten her stirrups to the appropriate riding length (which will differ, according to experience and riding discipline). With the stirrups the correct length, the knee should not come too far behind the flap (so the flaps do not provide any support), or too far in front (which will force the lower leg back and severely disrupt the balance of the rider.
- Position of the stirrup bars: riders should check that the stirrup bars do not stick out in such a way that the buckles of the stirrup leathers will cause bruising or rubs on their legs.
[edit] Places of manufacture
English saddles are made in many places around the world. A traditional manufacturing centre is in Walsall, England. Other countries that produce fine English saddles are Germany, Switzerland and the United States. Argentina produces many English saddles, particularly for the polo market, as well as a large number of brands that are in the mid-range of prices for other disciplines. The least expensive saddles are usually manufactured in India and can vary tremendously in quality of both workmanship and leather.
